High End Systems DL1 User Manual Page 67
- Page / 82
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
DL.1 User Manual General Maintenance and Troubleshooting 5-7
5
Replacing 2-Phase Board
To replace the 2-phase driver board:
1. Disconnect power to the fixture and allow it
to cool.
2. Unlatch the two rear latches and remove the
rear bezel.
Figure 5-5-1 shows the location of the rear
latches and rear bezel.
3. Use a 3 mm allen wrench to remove the
addressing screws and star washers.
4. Position new board against module aligning
the center top standoff. Place contact screw(s) in the appropriate position.
Note: When installing a replacement driver board on a module, always place a
star washer between an address screw and the pad on the logic board to
ensure good electrical contact.
5. Carefully replace the rear bezel, making sure to place (but do not force) the
gasket (shown in Figure 5-5-6) over the lamp cover located on the back of the
projector.
Replacing 3-Phase Board
To replace the 3-phase driver board:
1. Disconnect power to the fixture.
If the fixture has been operating,
allow the fixture to cool before
handling.
2. Facing the menu display with the
fixture upright, remove the six
M4 socket cap screws from the
left end bracket as shown in
Figure 5-5-7.
3. Slide the side assembly out of the topbox. The CPU board is on the base and two
3-phase boards are on either side of the assembly.
4. Use a 3 mm allen wrench to remove the addressing screws and star washers, (see
Figure 5-8 on page 5-10 for addressing screw location.
5. Position the new board against module aligning the center top standoff. Place
contact screw(s) in the appropriate position.
Note: When installing a replacement driver board on a module, always place a
star washer between an address screw and the pad on the logic board to
ensure good electrical contact.
Gasket
Figure 5-6 DL.1 Rear Gasket
Figure 5-7 Accessing CPU and 3-phase boards.
M4 socket
cap
screws
- User Manual 1
- Contacting High End Systems 2
- Declaration of Conformity 3
- Product Modification Warning 4
- FCC Information 4
- Important Safety Information 5
- Warranty Information 6
- Table of Contents 9
- Chapter 3: Fixture Operation 10
- Chapter 4: DMX Programming 11
- List of Figures 13
- Chapter 1: 15
- Features and Specifications 15
- Optional Accessories 16
- Specifications 17
- Projector Specifications 18
- Environmental Specifications 18
- Electrical Specifications 18
- Video Connectors: 19
- Chapter 2: 21
- Setup and Configuration 21
- Connecting Video 22
- Mounting the Fixture 24
- Mounting the Fixture Upright 25
- Truss Mounting 25
- Mounting Procedure 26
- Linking the Fixtures 27
- Setting up the Link 28
- Powering On the Fixture 29
- Viewing the Display Panel 30
- Setting the DMX Start Channel 31
- Shutting Down the Fixture 32
- Chapter 3: 33
- Fixture Operation 33
- The Menu Display 34
- Display in Menu Locked Mode 35
- Unlocking the Menu System 35
- Exiting the Menu System 35
- Menu Map 36
- scrolls between values 37
- selects 37
- Menu Option Descriptions 38
- Pan/Tilt Swap 39
- Pan Invert 39
- Tilt Invert 39
- Display Level 40
- Data Loss Timeout 40
- Projector Input Source 40
- Projector Default? 41
- Reset Projector Hours 41
- Striking the Projector Lamp 42
- Projector In By DMX? 42
- Iris Version 42
- Zoom Override Menu 43
- Focus Override Menu 43
- Projector Control 43
- Camera Option 44
- Align Pan Motors 45
- New Air Filter 45
- Fixture Mode Menu 46
- Test Options Menu 47
- Information Menu 48
- DMX Values Menu 49
- Temperatures Menu 49
- Display Errors 51
- Chapter 4: 53
- DMX Programming 53
- DMX Output Displays 54
- 16-bit DMX 54
- Parameter Descriptions 55
- Control Function Options 56
- DL.1 Protocol Tables 59
- Enhanced DL.1 Protocol 60
- Chapter 5: 61
- General Maintenance and 61
- Troubleshooting 61
- Replacing Parts 62
- Replacing the Lamp 63
- Replacing the Fuse 64
- M5 socket cap screws 65
- Phillips screws 65
- Replacing a Driver Board 66
- Replacing 2-Phase Board 67
- Replacing 3-Phase Board 67
- General Troubleshooting 68
- Table 5-1 LED States 69
- screw and LED locations 70
- Problem Solution 71
- Appendix 73
- Safety Information 73
- Appendice A 74
- Anhang A 75
- Apéndice A 76
- Vigtig Sikkerhedsinformation 77
- Appendix B: 79
- MSpeed Conversion Table 79
© 2020, manymanuals.com. All rights reserved. | 3.007 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals